Why Generator Pitch Matters: 2/3 vs. 5/6 Winding in Low and High Voltage Sets
Blog, Generator Buying Guide 04/03/2026
Why Generator Pitch Matters: 2/3 vs. 5/6 Winding in Low and High Voltage Sets
In the world of power generation, a small design choice can be the difference between a decade of stable power and a catastrophic “meltdown.”
Recently, on a busy construction site, a senior technician named Lao Zhang was commissioning two new units: a 400V Low Voltage (LV) set and a 10kV High Voltage (HV) set. A passing electrician glanced at the nameplates and asked, “Are the winding pitches the same on these two?”
Lao Zhang shrugged. “They’re both generators; how different could they be?”
The electrician smiled. “One choice could turn your LV neutral wire red-hot, while the other could trigger an insulation breakdown in your HV unit.”
This isn’t an exaggeration. Here is why the “Pitch” of a winding is the silent guardian of your power system.
1. Low Voltage Generators: The 2/3 Pitch Necessity

For Low Voltage units (400V/690V), we almost always use a Three-Phase Four-Wire system with a Neutral (N) line. This setup creates a path for 3rd-order harmonics.
The Recommendation: 2/3 Pitch Winding
A 2/3 pitch design is electromagnetically engineered to “cancel out” the 3rd harmonic and its multiples.
- Eliminates Neutral Current: By suppressing the 3rd harmonic at the source, we prevent current from stacking up on the neutral wire. This prevents cable overheating and fire hazards.
- Cleaner Sine Wave: With lower Total Harmonic Distortion (THD), the power quality is superior.
- Load Protection: Sensitive electronics (PLCs, sensors, medical equipment) are shielded from electromagnetic interference, and motors run cooler and quieter.
- Seamless Paralleling: Cleaner waves mean lower circulating currents between units, ensuring stable parallel operation without nuisance tripping.
The Risk of 5/6 Pitch in Low Voltage
Using a 5/6 pitch in a 400V system actually amplifies the 3rd harmonic. In a four-wire system, this leads to massive neutral currents, overloaded transformers, and a significant risk of equipment failure.
2. Medium & High Voltage: Why 5/6 Pitch is King

High Voltage units (6kV, 10kV, 13.8kV) typically utilize a Three-Phase Three-Wire system. Since there is no neutral path, 3rd-order harmonics have nowhere to flow.
The Recommendation: 5/6 Pitch Winding
In the absence of a neutral circuit, the 5/6 pitch becomes the superior choice for efficiency and insulation health.
- Higher Fundamental Efficiency: The 5/6 pitch maximizes the use of the copper windings, providing higher output power and better fundamental wave quality.
- Superior 5th & 7th Harmonic Suppression: While 2/3 pitch targets the 3rd harmonic, the 5/6 pitch is excellent at suppressing 5th and 7th harmonics—the exact frequencies that most threaten high-voltage insulation.
- Optimized Insulation Life: By reducing electrical stress at the winding ends, the 5/6 pitch extends the lifespan of the expensive insulation systems found in 10kV+ units.
The Drawback of 2/3 Pitch in High Voltage
Using a 2/3 pitch here is a waste of resources. You are paying for harmonic suppression that the system doesn’t need, while sacrificing the power density and insulation protection provided by the 5/6 pitch.
Summary Comparison Table
| Comparison Item | Low Voltage Generator | Medium & High Voltage |
| System Wiring | 3-Phase 4-Wire (with Neutral) | 3-Phase 3-Wire (no Neutral) |
| Recommended Pitch | 2/3 Pitch | 5/6 Pitch |
| Core Objective | Suppress 3rd harmonics; protect Neutral | Maximize efficiency; optimize waveform |
| 3rd Harmonic Impact | High risk; suppression is mandatory | No circuit path; not a primary concern |
| Power Quality | Pure waveform; low THD | High fundamental wave; low 5th/7th |
| Paralleling | Low circulating current; stable | Low circulating current; stable |
The Core Rule to Remember:
Low Voltage? Go 2/3 for Safety.
High Voltage? Go 5/6 for Performance.
Winding pitch is never a “guess.” It is a calculated balance between voltage level, system grounding, and insulation costs. Choosing the right pitch ensures your generator runs for decades; choosing the wrong one ensures it ends in a “bang.”
As a manufacturer with 20 years of experience, we ensure every generator we export is matched with the correct technical specifications for your local grid. If you have questions about choosing the right specs for your project, contact our technical team today.
Factory Direct Sales in China
Related Article – How to Choose the Right Alternator for Your Generator
Buying Diesel Generator Guide: How to Choose a High-Quality Alternator?
Comprehensive Guide for Standby Diesel Generator Set Selection
Buying Diesel Generator: How to Analyze the Alternator Quality?


